- GST: 27AAHFC0282F1ZP
- sales@coninsindia.com
- +91 9545521323
ISO 9001-2015, ISO 14001-2015, C-DOT APPROVED, MIL STANDARD MIL-I-46058-C TYPE AR, ROHS COMPLIANCES, REACH COMPLIANCES, G1 G2 G3 COMPLIANCES
PCB Conformal Coating Acrylcoat - ALQ-100
We are Manufacturer, Supplier, Exporter of PCB Conformal Coatings Acrylcoat ALQ 100, Acrylcoat Conformal Coatings and our setup is situated in Pune, Maharashtra, India. We target customers from ALL OVER THE WORLD.
Conins Acrylcoat is a high quality flexible, transparent, ECO FRIENDLY Acrylic Conformal Coating For PCB Assemblies. Acrylcoat HV60/HV100 are used where the coating thickness required is higher than usual and the working conditions are severe. This gives a thicker coating and it has to be cured in an oven at 80 deg.C for 60 - 80 mts. for best results.
Acrylcoat HV 60 and HV100 ensure protection for PCBs and components against moisture, Oxidation, fungus etc., when exposed to highly humid conditions. It is easy to apply and has good flexibility and gloss. Acrylcoat has high dielectric strength and it provides protection against high voltage arcing and corona shorts.
Special Features:
- Ozone Friendly
- Economical in use
- Good Dielectric strength
- Excellent adhesion to all Conformals
- Protects component leads from corrosion
- Contains UV Tracer for easy inspection
Applications :
- AEROSOL : Clean the Conformal thoroughly. Spray Acrylcoat from a distance of 25 cms. from the Conformal evenly. Allow the PCBs to dry in Air. Better results can be obtained if cured in a ventilated oven @ 60°C for 1 hr. The boards may be heated to 55 to 60°C just before spraying. SHAKE THE AEROSOL BOTTLE WELL BEFORE EACH APPLICATION
- LACQUER: ACRYLCOAT LACQUER can be applied by Brushing, Dipping or by Spraying. This can be used in a Dip Coating Machine or can be applied by a dispenser.
- REMOVAL: The coating can be removed using Conins Thinner AR.
- STORAGE: Store in a cool dry place below 40°C. Keep away from naked flame or flammable material. The contents are highly inflammable. Destroy the container after use.
- PRECAUTIONS: Acrylcoat is a flammable material. Contact with skin or eyes and inhalation should be avoided. In case of contact, wash the affected areas with soap and plenty of water. Keep away from open flames and Flammable material. Use in an adequately ventilated area only.
- Shelf Life : 2 years for Aerosol and 1 year for Lacquer = in original sealed containers.
- Packing : 500 ml. Aerosol Spray containers
- LQ : 1 litre, 5 litres, and 25 litre containers.
- APPROVED BY C - DOT. CONFORMS TO MIL 46058C Type AR.
| PRODUCT CODE | Acrylcoat - ALQ-100 |
|---|---|
| Appearance (Liquid & Coated Film) | Clear / Transparent / Smooth & Glossy |
| Specific Gravity (Density @25°C) | 0.85 to 0.91 |
| Viscosity @25°C | 100 - 105 sec (Zans Cup #2) |
| Flash Point | < 79°C |
| Comparative Tracking Index (CTI Value) | 600 |
| Coating Thickness (Single Coat) | 45 - 50 μm Recommended |
| Dielectric Strength | 25 KV/mm |
| Thermal Cycling (MIL-I-46058-C-AR) | Passes as per MIL-STD |
| Moisture Resistance (MIL-I-46058-C-AR) | Passes as per MIL-STD |
| Insulation Resistance (MIL-I-46058-C-AR) | Passes as per MIL-STD |
| Fungus Resistance (MIL-I-46058-C-AR) | Passes as per MIL-STD |
| Withstand Temperature (Film) | -50 to 130°C |
| Coverage Area (20 μm Film – 500 ml Aerosol) | 4 - 5 m² |
| Film Traceable | Under UV Lamp |
| Drying Time (Touch to Dry) | 10 - 15 Min @ Room Temp. |
| Hard Dry | 2 Hrs @ Room Temp. |
| Pre Heating of PCB @50°C (Touch to Dry) | 3 - 5 Min |
| Post Heating of PCB @50°C (Hard Dry) | 10 - 15 Min |
| Curing Time | 12 - 24 Hrs |
| Optimum Properties | 7 Days |
| Packing | 1, 5, 25 Litre |
